Ramp Inspection and Play Testing
Each joint, bush and link is loaded with a bar with the wheels off the ground. It is the only way to separate a worn bush from a worn ball joint, and it is what stops a knock turning into a list of parts.
Light cars with a torsion beam at the back on much of the range, which has one specific wear item that is easy to miss. Al Zaabi Autocare carries out Renault suspension and shock absorber repair in Mussafah, Abu Dhabi, across the Duster, Koleos, Megane, Captur and Talisman.

Send the model and the mileage. We come back with the scope and a price before any work starts.
Suspension is measured before it is quoted. A knock has several possible sources and only one of them is yours, so everything is checked on the ramp against the other side of the car.
Open the full list below for everything a Renault suspension repair covers, and what each part of it involves.
Each joint, bush and link is loaded with a bar with the wheels off the ground. It is the only way to separate a worn bush from a worn ball joint, and it is what stops a knock turning into a list of parts.
Dampers are checked for leaks, for bump stop damage and for how the car settles after being pushed down. Heat kills damper oil quietly, and a tired damper ruins tyres long before it fails outright.
Broken springs are more common here than owners expect, and a car sitting low on one corner with a knock over bumps is usually a spring rather than a damper.
Collapsed top mounts and seized top bearings read as heavy steering at parking speed and a creak on lock. Both are replaced with the strut rather than after it.
Control arm bushes perish in this heat and take the geometry with them. They are replaced in axle pairs so the car sits, steers and wears its tyres evenly.
The cheapest parts on the car and the loudest. A worn drop link is a rattle over rough surfaces, and left alone it wears the anti-roll bar bush it works against.
Bar bushes dry out and clonk. The bar, its mounts and its links are treated as one assembly because replacing one of the three rarely ends the noise.
Where the car rides on air, the compressor, dryer, valve block, height sensors and springs are tested as a system and the fault found before anything is replaced.
Electronically controlled dampers are read for circuit faults and commanded through their range, so a control fault is not treated as a worn damper or the other way round.
Every suspension job finishes on the alignment rack at the car's specified ride height. New parts move the geometry, and leaving it is how a repair turns into a set of tyres.
Suspension wears in a predictable order on any given car. Knowing the order is what stops a knock turning into a list of parts.
The rear beam runs on bearings that wear, and the symptom is a knock from the back and rear tyres wearing unevenly. It is a known item and it is checked with the beam loaded.
Wear gives vague steering and a knock over sharp edges. Each joint is loaded individually so the quote covers what is worn.
Dampers lose their oil quietly in this heat, and a car that floats after a dip is telling you before it makes any noise.
The cheapest parts and the loudest. A rattle over rough surfaces usually starts here and stays cheap only while it is a rattle.
New parts move the geometry, and on a light car that shows up quickly as uneven tyre wear.
Inspect, quote, replace in pairs, align, road test.
The car goes up and every joint is loaded and compared with the other side. You are shown what moves and what does not.
What is worn, what is worth doing now and what can safely wait, priced before anything is ordered.
Parts replaced in axle pairs where the job calls for it, to the manufacturer's torque figures, with bushes pressed rather than forced.
Four-wheel alignment at the correct ride height, then a road test over the surfaces that showed the fault in the first place.
What you drive away with after a Renault suspension repair, beyond the invoice.
The knock over expansion joints and the creak on lock are gone, which on most cars is the whole reason the owner booked it in.
A car that holds its line instead of wandering, and a wheel that sits straight when the car does.
Worn suspension eats tyres from the shoulder inwards. Fixing it and aligning it is usually cheaper than the tyres it saves.
A damper that cannot control the wheel lets it skip under braking. Brakes get the credit for stopping the car, but the suspension decides whether they can.
Not an extra line on the bill. If the work moved the geometry, setting it back is part of the work.
You are told which joint was worn and shown the movement, rather than sold the whole corner because something in it knocked.
Find yours below. If it is not listed it is still covered, so call the workshop and ask.
Suspension rarely fails all at once. It degrades until the car feels normal to you and wrong to everybody else.
The most common complaint and usually the cheapest: a drop link, a bush or a top mount. It stays cheap only while it is still a noise.
One corner down overnight is a broken spring or an air system losing pressure. The whole car down is the air system or worn springs all round.
A shoulder worn away on one edge is the suspension telling you about itself in the only way it can. Read it before you buy tyres.
The car needs constant small corrections to hold a lane. Usually bushes, a ball joint or geometry that has moved.
More than one rebound after a dip means the damper is no longer controlling the spring, whatever it looks like from outside.
Oil down the body of a shock absorber means it has lost its seal, and once it has, it is not damping anything.
On adaptive or air-sprung cars this is a stored fault with a circuit attached to it, and it is readable rather than a mystery.
An air compressor that runs for a long time or runs often is working around a leak, and running it that way is what kills it.
Tell us the model and what it is doing. You get a free 360-degree health check and a written price before any work starts, at Plot no 69, Mussafah M-37, Abu Dhabi, UAE.
This page is one job on one marque. The Renault page covers everything else that car needs, and the suspension repair page covers the same work on any other car.
German, American, Italian, British, Japanese, Korean and Asian marques, from a daily Corolla to a Rolls Royce.
Not listed? Send us the make and model and we will confirm the same day.
Two fixed lists of work, written down before anything starts. Both come with a free health check, a wash and a vacuum.
Both packages are quoted per car. Call +971 50 187 3124 with the model and we will confirm the same day.
Unedited reviews from Google, the same ones you will find if you look up the workshop yourself.
594 Google reviews
Newest reviews first.
Plot 69, Mussafah M-37. Purpose-built bays, a body shop and a detailing bay under one roof.



What Renault owners ask before booking a suspension repair in. If yours is not here, call the workshop and ask.
On a car with a rear torsion beam that is very often the beam bearings, which is a specific and known wear item. It is checked with the beam loaded rather than by looking at the dampers.
Usually not, if it is dealt with as a knock. Links, bushes and mounts are inexpensive, and it is what they wear out next that costs money.
Yes. A new damper on one side and a tired one on the other makes the car brake and corner unevenly, which is worse than two matched but worn ones. Bushes, links and joints are replaced where they are worn, side by side.
Four-wheel alignment is part of the job wherever the work moves the geometry, which is almost every suspension repair. It is done at the car's specified ride height, not at whatever height it happens to be sitting.
Less than the service schedule assumes. Heat hardens rubber and the road surface loads it, so bushes, top mounts and links wear faster here than the figures written for cooler countries.
Both. Compressors, dryers, valve blocks, height sensors and lines are repaired or replaced individually once the system has been tested. Replacing the whole system because one corner drops is how people overpay.
Free 360-degree health check and a written quote before any work starts. Tell us the model and the symptom, and we will come back with the scope and the price.